What are the RF calibration standards for defence and aerospace manufacturers?

Defence and aerospace manufacturers calibrating RF test equipment must typically satisfy DEF STAN 05-055 for UK Ministry of Defence (MOD) contracts, NATO AQAP 2110 for allied defence programmes and AS9100D clause 7.1.5 for aerospace quality systems, with ISO/IEC 17025 setting the standard for the laboratories that perform the work.

Together, these standards require RF instruments such as signal generators, spectrum analysers and power meters to be calibrated at defined intervals, traceable to national standards, with documented uncertainty and formal out-of-tolerance reporting. In practice, the MOD treats certificates from ISO/IEC 17025-accredited laboratories, such as those accredited by UKAS, as the primary evidence of traceability.

Which standards govern RF calibration in defence and aerospace?

No single standard is written exclusively for RF calibration. Instead, general measurement and quality standards apply to all test and measurement equipment (TME), including RF and microwave instruments.

Standard  Applies to Key calibration requirement
DEF STAN 05-055 Part 01 (Issue 4, 2024) MOD contracts involving TME Traceability to national or international standards, a 4:1 uncertainty ratio and out-of-tolerance reporting
AQAP 2110 Edition D NATO defence suppliers Measurement and calibration system must meet ISO 10012:2003
AS9100D clause 7.1.5 Aerospace quality management systems Equipment register, defined intervals, traceable calibration and assessment of previous results
ISO/IEC 17025:2017 Calibration laboratories Technical competence, measurement uncertainty and certificate content

For a broader introduction to the discipline itself, read our guide to what RF and microwave calibration is.

What does DEF STAN 05-055 require for RF test equipment?

DEF STAN 05-055 Part 01 requires that "all TME shall be calibrated and be traceable to National or International Standards", and it defines three levels of traceability that contracts can specify:

  • Level 1: calibration by a laboratory accredited to ISO/IEC 17025 for the measurements concerned
  • Level 2: calibration to a documented method by competent staff, using reference equipment calibrated by a competent, traceable laboratory
  • Level 3: a certificate of conformance from the manufacturer or another appropriate organisation

The standard also sets a Test Uncertainty Ratio of 4:1, stating that the uncertainty of the measurement standards "shall not exceed 25% of the acceptable tolerance" where no specific calibration procedure applies. At microwave frequencies, where connector repeatability and mismatch add to measurement uncertainty, meeting this ratio against tight power or attenuation tolerances requires low-uncertainty reference standards and specialist laboratory capability.

Why is UKAS accreditation often a contractual requirement?

UKAS accreditation is often a contractual requirement because DEF STAN 05-055 states that "calibration certificates that do not bear an accreditation mark will not be regarded by the MOD as providing evidence of traceability."

UKAS is the UK's national accreditation body, so a UKAS-accredited certificate is the simplest way to demonstrate Level 1 traceability. Prime contractors frequently flow this requirement down their supply chains. Importantly, accreditation is scope-specific: an RF calibration is only accredited if the laboratory's schedule covers that quantity and frequency range, so it is worth checking a provider's schedule rather than relying on the UKAS logo alone.

What do AQAP 2110 and AS9100 add?

AQAP 2110 requires that the "measurement and calibration system applied to the contract shall meet the requirement of ISO 10012:2003", the international standard for measurement management systems. It also obliges suppliers to inform the Government Quality Assurance Representative (GQAR) when equipment fails calibration in a way that affects delivered products or acceptance results.

For aerospace manufacturers, AS9100D clause 7.1.5 requires a controlled register of measuring equipment, defined calibration intervals and calibration against standards traceable to international or national standards, with documented uncertainty.

What happens if RF test equipment is found out of tolerance?

When RF test equipment is found out of tolerance, defence and aerospace manufacturers must record the as-found results, assess the impact on previous measurements and, under MOD contracts, report the non-conformance.

DEF STAN 05-055 requires non-conformances to be reported to the MOD before adjustment or repair, with measured values recorded before and after adjustment on an out-of-tolerance report. Under AQAP 2110, the GQAR or acquirer may require affected measurements to be repeated. For RF equipment, the stakes are high: a power sensor reading 0.5 dB out could mean radar, radio or EMC test results have been accepted on inaccurate data, potentially triggering re-testing of delivered products.

UKAS-accredited RF calibration with DM

DM Calibration is UKAS Calibration Laboratory No. 0143, accredited to ISO/IEC 17025:2017, and a Specialist Service Provider to the UK Ministry of Defence. Our UKAS schedule of accreditation covers RF power, attenuation and reflection coefficient up to 18 GHz, and frequency measurement up to 40 GHz, supporting Level 1 traceability under DEF STAN 05-055. Explore our electrical and RF calibration services or learn more about UKAS calibration with DM by downloading our guide below. 

Book your calibration now

Our experts are on-hand to handle all of your calibration needs.